SIXAXIS PAIR TOOL NOT WORKING HOW TO
SIXAXIS PAIR TOOL NOT WORKING SERIAL
SIXAXIS PAIR TOOL NOT WORKING SOFTWARE
SIXAXIS PAIR TOOL NOT WORKING CODE

SIXAXIS PAIR TOOL NOT WORKING SERIAL

To see if Bluetooth (classic) on the ESP32 worked at all, I've successfully ran the example sketches from ESP board manager/libraries for BT serial to serial connection with my Android phone (Serial Bluetooth Terminal App), exchanging messages from phone to ESP32. I have tried this with both PS3 Controllers I have and on different ESP32 (NodeMCU 32s)вЂ¦many, many times! LEDS keep flashing for a good minute, even if I hit reset on the ESP32, it does not pair (in the videos, you'll see the pairing is very fast). I then push the connect button on PS3 (tried momentary, holding down etc), the '1,2,3,4' LEDS on the PS3 controller fast flash as it tries to pairвЂ¦but nothing then happens. Opening the Serial Monitor, when powered up/reset by the EN button, you see start up texts, ending inВ 'Ready'.

SIXAXIS PAIR TOOL NOT WORKING CODE

Having written the BT MAC into the code and to the PS3 controller via the Sixaxis pairing tool, then successfully compiled and uploaded. In theory, given PS3 controller now has the ESP's BT MAC written in, all I should need to do is write in the same matching MAC address (of the ESP, I presume, as that's what tutorials say and see above). Have also used the example sketch 'PS3Connect', that comes as part of the PS3 Controller library. On the ESP32 side, I've downloaded the libraries and all the alternative codes from these sites into Arduino IDE. Note also that when inputting this to rewrite the MAC stored in PS3 controller, it 'corrects' any upper case letters into lower case (so when you check what's in there afterwards, it's 7c:9e. This might be relevant to the subsequent problemвЂ¦ Line above the MAC says Failed to enable bluedroid. Note : there's an interesting warning message that comes up in Serial Monitor when retrieving the MAC address. This is the format it gives, and which I then rewrote into the PS3 controllers: It would appear (unless I've got this wrong?) that we therefore need to give the PS3controller the ESP32's own BT MAC address using this rewrite software.ДЄccordingly, I discovered the ESP32's BT MAC address (one digit different from its wifi MAC address) using:

SIXAXIS PAIR TOOL NOT WORKING SOFTWARE

I downloaded and successfully used the sixaxis pair tool software that reads/can rewrite the Bluetooth MAC address stored in the PS3controller, via plugging in USB micro B to PC (despite what it says in the robotic arm video, it seems that that is the address for the PS3 console itself which the PS3controller needs in order to connect/pair this holds true in that if I change it, it won't pair to PS3 console, then it gets changed back (either in the software or by plugging PS3controller to console on USB to reset it) and works again).

SIXAXIS PAIR TOOL NOT WORKING HOW TO

I'm working in the Arduino IDE as that's all I know how to use right now (conscious that ESP32 IDF software is also out there, perhaps might need to be part of solution.?).Д«ut it doesn't work! Can't connect the PS3 controllers to ESP.here's more detail and example code at the bottom: I have tried sketches from all these sites, and also the simplest example, called 'Ps3Connect' that comes with the PS3Controller.h library (see below). Page and video called 'PS3 Controller + esp32 + robotic arm = awesome! (Building a wireless esp32 powered robotic arm)'В at these links: In theory, this should be feasible with ESP32 and give inputs from all buttons/joysticks on the controller here are some links to videos and tutorials (note there's some bad info in first one which will detail below), that come with all the code and instructions, and link to the software mentioned: This is so that I can then use it as a controller for robot car projects etc. From herein, I'll use the terms PS3controller and ESP32 to avoid any confusion over the term 'controller'. I am trying to get my ESP32 (specifically, ESP32S Node MCU dev kit v1) to pair/connect with old Playstation3 (PS3) game console controller (I have 2 of these, specifically official Sony PS3 sixaxis dual shock), using the BT classic capability. In at the deep end here, so will put in as much detail on the issue and what I've tried so far as possible. This is my first time asking for help on here, just joined and I'm new to electronics.

Sixaxis pair tool not working